TABLE OF CONTENT

CHAPTER ONE

                                                    INTRODUCTION

1.1            THE AIM AND OBJECTIVES OF THE PROJECT

1.2                 JUSTIFICATION OF THE PROJECT

1.3                 THE SCOPE OF THE PROJECT

1.4         THE PROJECT   REPORT ORGANIZATION

CHAPTER TWO

LITERATURE REVIEW

2.1      TECHNOLOGY

2.1.1   FEATURES OF THE MICROCONTROLLER

2.1.2   DESCRIPTION

2.1.3   PIN DESCRIPTION

2.2   WORKING PRINCIPLE

2.3      MAJOR COMPONENTS

2.3.1   POWERS SUPPLY UNIT

2.3.2     THE DISPLAY UNIT

2.3.3     THE OPTOCOUPLER

2.3.4     THE RELAY MODULE

2.4        PROGRAMMING LANGUAGE

CHAPTER THREE

METHODOLOGY

3.1      INFORMATION GATHERING

3.2      PROJECT ANALYSIS

3.3      SYSTEM DESIGN APPROACH

3.4      DETAIL OF THE DESIGN

CHAPTER FOUR

DESIGN AND CONSTRUCTION OF THE HARDWARE

4.1        OTHER COMPONENTS

4.1.1     TRANSFORMER

4.1.2       DIODES

4.1.3     RECTIFIERS

4.1.4   CAPACITORS (SMOOTHING)

4.1.5   SEVEN-SEGMENT DISPLAY

4.1.6 TRANSISTORS

4.1.7   THE OPTO COUPLER

4.1.7.1    THE PHOTORESISTOR

4.1.7.2    THE LIGHT EMITTING DIODE (LED)

4.1.8     RESISTORS

4.1.9     RELAY

4.1.10      VOLTAGE REGULATOR

4.2.1     TESTING OF THE INDIVIDUAL COMPONENTS.

4.2.2   UNIT BY UNIT TESTING

.2.3      SYSTEM TESTING.

4.3           PACKAGING

CHAPTER FIVE

CONCLUSION AND RECOMMENDATION

5.1           CONCLUSION

5.2           SUGGESTION FOR FURTHER IMPROVEMENT

5.3           RECOMMENDATIONS

BIBLIOGRAPHY

CHAPTER ONE

                                                    INTRODUCTION

The industrial batch counter is an electronic and electrical device that handles the counting and controls the flow of individuals using an automated slide door that allows access only when the administrator permits. The technique involved in the design is a simple sensor unit that opens and closes the door when someone obstructs the light path. These parameters can be used to determine when someone has moved in or out of the conference hall (for instance). The light sensing type involves monitoring the unit with photon or optical devices; this consists of the encoder (transmission path or the source of energy) and the decoder (receiver unit that converts the light intensity to electrical signal). An LED emitter, combined with a photo detector (Light Dependent Resistor, photo transistor or infrared sensing diode) in proximity, form a very useful object called opto-coupler or opto-isolator. When the opto coupler is obstructed, the door opens and the display shows an increase or decrease of individuals in the room (depending on the path followed). This project report creates a greater picture of the industrial batch counter.

1.4            THE AIM AND OBJECTIVES OF THE PROJECT

The aim of this project is to demonstrate a smart device that counts the number of people inside a conference hall; and prevents people from entering once the room has reached its capacity.

1.5                 JUSTIFICATION OF THE PROJECT

The need for counting the number of persons inside the conference hall is for statistical record, which will help the conference hall management take a proper account of people; and as well, control the conference hall capacity from being over populated.

1.6                 THE SCOPE OF THE PROJECT

This project covers the features of the capacity monitor, the hardware description, the use of transistor-transistor logic and microcontroller, how the system works and its applications.

1.4    THE PROJECT   REPORT ORGANIZATION

This project report is organized into five chapters. The first chapter covers the introduction, aim scope and justification of the project. The second chapter talks about the technology behind the project, the description of the microcontroller, as well as the working principle of the project. Chapter three covers the methodology of the project. Chapter four discusses the designing and construction of the project, as well as other components used in designing this project. Chapter four also talks about the testing of the individual components and packaging of the project. And lastly, chapter five summarizes and concludes the project.

Buyers has the right to create dispute within seven (7) days of purchase for 100% refund request when you experience issue with the file received. 

Dispute can only be created when you receive a corrupt file, a wrong file or irregularities in the table of contents and content of the file you received. 

ProjectShelve.com shall either provide the appropriate file within 48hrs or send refund excluding your bank transaction charges. Term and Conditions are applied.

Buyers are expected to confirm that the material you are paying for is available on our website ProjectShelve.com and you have selected the right material, you have also gone through the preliminary pages and it interests you before payment. DO NOT MAKE BANK PAYMENT IF YOUR TOPIC IS NOT ON THE WEBSITE.

In case of payment for a material not available on ProjectShelve.com, the management of ProjectShelve.com has the right to keep your money until you send a topic that is available on our website within 48 hours.

You cannot change topic after receiving material of the topic you ordered and paid for.